Connectors for heavy duty, self-protected thick-walled microducts.
Télécharger fiche technique
Direct-buried, wraparound duct closure for pre-installed microduct systems, including port reducers. Wraparound duct closure couples two HDPE ducts with pre-installed microducts (JetNetXS, with or without resident cables) or tight-bundled microducts (MultiNetXS). Provides sufficient space for the microduct connectors.
Branch connectors for Outside Plant (OSP) application in Y-type configurations. Designed as a microduct manipulation point for branching off any microduct at any location in the network. Can be used for branching JetNetXS and MultiNetXS to JetNetXS, MultiNetXS and EaseNetXS.
Branch connectors for Outside Plant (OSP) applications in Y-type configuration. Designed as microduct manipulation point for branching off any microduct at any place in network. Draka’s microducts are designed for blowing into protective plastic ducts, and have superior blowing characteristics.
Branch connectors for Outside Plant (OSP) applications. H-branch connector is a microduct manipulation point and also used for branching large numbers of microducts. T-branch designed for semi-redundant (flat ring) branching in ring-shaped network. Port reducers available to adapt standard H-type and T-type branch connectors to configure with other main-branch duct sizes.
Protective duct (16, 25, 40 and 50 mm) rubber sealing plug. Used for sealing duct ends after installation of microducts into ducts. Watertight, wide range of diameters, easy installation.
Coupling set to connect two protective HDPE ducts (16, 25, 32, 40 and 50 mm) with pre-installed microducts. Leaves sufficient space to connect all microducts inside.
Wraparound Sealing Plug for JetNetXS ducting system. Seals duct ends to make them fully gas and watertight.
Direct-buried Wraparound Duct Closure for pre-installed microduct systems. Couple two or three HDPE ducts with pre-installed microducts or resident cables. Closure provides enough space for the microduct connectors. Port reducers available for ducts smaller than 40 mm.
Modular, highly reliable, robust, high-pressure and crush resistant microduct connectors with superior blowing capabilities. Designed to connect and terminate microducts at any point in the network. Locking clips secure connectors after installation. Can be unlocked if necessary.
Wraparound sealing plug for JetNetXS ducting system. Uused for sealing interstices between microducts and the HDPE duct in hand holes, buildings, street cabinets, etc. Sealing plug is fully dividable and provides tension relief. Plug watertight up to 0.2 bar according to IEC 60794-1-2-F5a. Plug gastight according to Dutch standard NEN 2768-2005.
Coupling for universal, heavy-duty HDPE protective ducts for installation of microducts. Used in Outside Plant (OSP) networks, usually in feeder and distribution part of Fiber-to-the-Home network. Draka’s HDPE protective ducts used to install microducts for blowing. HDPE protective duct can be direct-buried without additional physical protection. Meet same criteria as ducting specifications.
Reducer connector set to connect microducts of different sizes (5, 7, 10, and 12 mm).
Reducer for universal heavy-duty HDPE protective ducts for microduct installation.
End-stop for universal, heavy-duty HDPE protective ducts for microduct installation.
Dividable coupling for universal, heavy-duty HDPE protective ducts used to install microducts in Outside Plant (OSP) networks, usually in feeder and distribution part of Fiber-to-the-Home network. Dividable couplings meet same criteria as ducting specifications
Highly reliable sealing tape for repairs. Used for sealing irregular shapes. Watertight and protects against corrosion.
Universal Polyurethane (PUR) sealing plugs, used for:
The connectors are designed to connect and terminate the microducts. Locking clips secure the connectors after installation. If necessary the connector can be unlocked after removal of the locking clip
The Split connector is designed as a microduct manipulation point; for forking microducts at any location in the network. The closure provides enough space for microduct connectors and ensures the watertight integrity of the ducting system.
Heat shrinkable end-caps type 1 - 6 are used to seal the ends of the cables or ducts. They are designed to prevent moisture or dirt from entering the cables or ducts while giving mechanical protection. Similarly, end-caps type A, B and C are used for temporary closure of microducts to keep them safe from moisture or dirt during installation and storage.
Microduct Cutter, Blow-in Cap (microducts), Blow-in Cap (cable), Sheath Cutter, Splay Tool, Sheath Cutter (for Riser cable), etc.
With the dividable repair set a damaged protective duct can be repaired without interrupting microducts or cables in the duct. The duct repair set is also capable to enclose a number of microduct connectors if both the protective duct and the microducts are damaged.
Draka’s pre-ferruled BendBrightXS cables take microduct jetting solutions to the next level: all the same benefits but even quicker to install. Unique installation techniques reduce installation times and costs while maintaining high quality standards
Support des ventes
P: +34 942 24 71 00
Laissez-nous vos coordonnées et nous prendrons contact avec vous dès que possible
Je voudrais en savoir plus sur ...
Envoyez votre demande directement à notre service commercial local via le formulaire ci-dessous.
Trouvez votre produit:
A propos de Draka Communications
NExsT: magazine semestriel Draka
Quoi de neuf?